Bluetooth Controller, 4x 6.5" Marine RGB LED Speakers, Amplifier W/Wiring Kit
The Infinity by Harman INF-BC4 Pre-Amp Bluetooth Controller allows consumers to pair his/her media device, and control basic functions through the Infinity controller. This stand-alone audio device features a rotary encoder and large buttons. Add an amplifier, speakers, pair, and stream from the Infinity by Harman BT controller. Easily control the volume of your Bluetooth audio with the rotary controller. IPX6 Waterproof and ready for outdoor use; no need to worry about the forecast. Requires 1 3/8" diameter hole to secure firmly in place.
General Features:
- Requires 12V power source
- Requires 1 3/8" diameter hole
- Internal Blutetooth chipset
- Dimensions (W x D)2" x 2"
- Wireless Bluetooth Streaming
- Rotary Encoder
- IPX6 Waterproof
- Flush Mount
- Large Buttons
- Durably Constructed
UPC Code 050667372866
These Infinity KAPPA 6.5" 2-Way 300W Marine Speakers features multi-color LED lighting, Plus One polypropylene woofer and midrange cones, Mylar tweeter domes, SSI (Switch Selectable Impedance) 2 or 4 Ohm option, one piece cast polymer baskets, sealed magnets, and rubber woofer surrounds for high SPL performance. UV resistant marine grade IPX3(IPX5 from front) weather resistant. (Titanium)
General Features:
- 6.5" 2-way speakers (Pair)
- Marine-Grade
- Multi-Color RGB LED Lights
- Plus One Woofer Cone
- Grille-Mounted Mylar Tweeter
- One-Piece Cast Polymer Basket
- IPX5 Rated for Water Resistance
- Power Handling: 100 watts RMS (300 peak)
- Sensitivity: 92 dB at 2.83 volts
- Frequency Response: 40-25,000 Hz
- Impedance: 3 ohms
DO NOT USE DRILLS ON THE SCREW SPEAKER TERMINALS EVER.
Loosen and Tighten BY HAND ONLY. Using a Drill snaps the solder connection on the back of the terminal and the X-over (coax) Circuit board.
UPC Code 050667373078
Infinity's marine 3004A amplifier will add plenty of muscle to your music without breaking a sweat, and it'll look good doing it. This 4-channel powerhouse delivers 75 watts RMS to each of the front and rear speakers in your boat. Into planning ahead? You could use this amp in 2-channel mode now to drive a couple subwoofers with 200 watts RMS each, then reassign it to your front and rear speakers when you get a bigger sub amp. Speaker-level inputs allow this amplifier to work in almost any system, even if you're keeping your marine's factory radio. You can use the separate high and low pass filters on the front and rear channels to maximize the performance of your speakers or subs.
General Features:
- 4 Channel Marine Amplifier
- 75 watts RMS x 4 at 4 ohms
- 100 watts RMS x 4 at 2 ohms
- 200 watts RMS x 2 at 4 ohms in bridged mode (4-ohm stable in bridged mode)
- Class H amp technology
- Variable high and low-pass filters on front and rear channels
- Preamp and speaker-level inputs
- Preamp outputs
- Fuse rating: 30A x 2
- 8-gauge power and ground leads recommended
- Wiring and hardware not included
UPC Code 050667380106
The Power Sport Motorcycle Universal Amplifier Wiring Kit includes the following 6 foot length of red and black T-Spec OFC power and ground wire with a T-Spec V8MANL fuse holder, 60 amp fuse protected by a black nylon braid, Pre-terminated ring terminals, (2) 4 foot pieces of 16 gauge OFC speaker wire protected by black nylon mesh and 4"x6" hook and loop mounting pad for micro-amplifiers.
Amplifier Wiring Kit:
- Designed tor motorcycles
- 6 feet of red and black T-Spec OFC power and ground wire with a T-Spec V8MANL fuse holder and 60 amp fuse protected by a black nylon braid
- Pre-terminated ring terminals make connections to the battery simple
- Two 4 foot pieces of 16 gauge OFC speaker wire protected by black nylon mesh makes upgrading the factory speaker wires or adding new speakers a smart choice
- Upgrading Harmon Kardon System – Two 47-ohm .5 watt resistors to keep the factory radio outputs active
- All the necessary installation hardware is included along wtth a 4 × 6 inch hook and loop mounting pad for micro-amplifiers to hold the amplifier securely in place
UPC Code 086429332267