Harley Install FLHC Bluetooth Adapter Kit, Amplifier Set Up, 6.5" Kicker Speaker
This Pioneer DEH-S420BT CD receiver with enhanced audio functions is the perfect receiver product to take your vehicle's audio system to the next level. It features USB/AUX inputs, built-in Bluetooth, voice control, AM/FM tuner, and Pandora/Spotify control. The LCD Display with LED backlighting gives you a display front interface! Connect to your smart device and stream all your favorite tunes! Or pop in a CD and let the music reverberate through the air!
General Features:
- Single DIN
- CD Player
- Buil-In Bluetooth
- USB/AUX Inputs
- Pioneer Smart Sync App
- Apple/Android Compatible
- FLAC Playback
- 13-Band Graphic EQ
- MOSFET 50W x 4 Amp
- Spotify Control
- Anti-Theft Detachable Panel
- External Bluetooth Mic
- Quick Charge for Android
- Listening Position Selector
- High/Low Pass Filter
- Subwoofer Control
- Advanced Sound Retriever
- RDS Tuner
- Best Stations Memory
- 10 Steps Brightness Control
UPC Code 4988028433993
The BC-HDSWC-WR Harley-Davidson Handlebar Control allows installers to replace the radio in a motorcycle, while retaining the use of the factory handlebar audio controls. This easy-to-install interface uses a patented Auto-Detect system to configure itself for the specific motorcycle application and aftermarket radio being installed. The interface provides wires for front speakers, constant power, switched power and ground, and includes a water-resistant enclosure. This product works with the 95-HDIF2 Harley-Davidson Road Glide FLT/Sharknose fairing (sold separately). It can be made to work with all models by pairing with Metra’s BC-9725 Amp Bypass Harness.
General Features:
- Retains the factory handlebar audio controls
- Auto-Detect configures itself for the specific motorcycle application and aftermarket radio
- Comes with a plug-n-play harness in a water-resistant case
- Provides wires for speakers, constant power, switched power and ground
- Use the BC-9711 to retain rear speakers
- This part number replaces the HD-ASWC-1
Note:
- Fits Harley-Davidson FLH & FLT 1998-2013 (FL models with a fairing)
- Must be without factory amplifier, 2 speaker systems only
UPC Code 086429415762
Enrocks EHDRAB98-13 allows you to install a single din receiver into your Harley Touring Bike. The wire harness is included with the dash kit to make wiring more convenient.
General Features:
- Single DIN radio provision
- For Harley Davidson (FL models with fairings) Touring 1998-2013
- Gapless fit between the dash and the kit
UPC Code 728120484431
These CS-Series 6-1/2-inch Coaxial Speakers are the perfect way to upgrade your factory speakers. CS-Series Coaxials deliver remarkable performance and ultra-clean bass with a heavy-duty motor/magnet structure not found in stock speakers. The stamped-steel framework supports a rigid polypropylene cone with EVC (Extended Voice Coil) technology for the best sonic quality. Using zero-protrusion PEI tweeters with neodymium magnets, you get the clarity you need without interfering with factory grilles. These CS speakers work best with 100 watts of recommended power.
General Features:
- 6.5" 2-Way Design Speaker
- 300W Peak Power
- 100W RMS Continuous Power
- 90dB Sensitivity
- 40-20kHz Effective Frequency Range
- Zero-protrusion tweeters to fit nearly any factory depth
- UV-treated poly-foam surround resists heat or direct sunlight
- Large woofer magnet in a heavy-duty motor for ultra-clean bass
- PEI-tweeter construction provides superb clarity
- Neodymium tweeter magnets allow for increased volume in high frequencies
- Steel mesh grilles included for speaker protection
UPC Code 713034088363
Enrocks EHDSA98-13 brackets will allow you to install select 6 1/2" or 6-3/4" speakers in the factory speaker openings of select 1998 - 2013 Harley Davison Bikes.
General Features:
- 6-1/2" - 6-3/4" Speaker Adapter Plate
- For 1998-2013 (FL models with fairings) Harley Davidson Touring
- Gapless fit between the speaker and the kit
- High-grade ABS plastic construction
- Color: Black
UPC Code 728120484486
Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit
General Features:
- 1 x 10 mm^2 Power Wire (red), flexible Strands (0,15 mm), 5 m
- 1 x 10 mm^2 Ground Wire (grey), flexible Strands (0,15 mm), 0.8 m
- 1 x RCA Stereo Audio Cable (blue), double shielded, 5 m
- 1 x 0.5 mm^2 Remote Wire, 5 m
- 1 x AGU Fuse Holder with 40 A ANL Fuse
- Installation Kit
Installation Instructions:
- Disconnect at first the negative ground connection from the vehicle’s battery.
- Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND contact point. Ensure that all paint or other insulation is removed from around the hole area.
- Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
- Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the supplied ring terminals.
- Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
- Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
- Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier, when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
- At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock consists. Then re-connect the negative ground connection to the vehicle’s battery.
UPC Code 854932002478
This Infinity Primus 6002A 2-Channel amplifier is a result of arduous testing and quality control. This amplifier features an input level control adjusts input sensitivity. When low level inputs are used, this control can adjust the input between 200mVrms and 5.0Vrms. When high level inputs are used, the control adjusts the input between 0.5Vrms and 15Vrms. Black with grooved center panel, polished badge, black painted end panels and bottom, this Infinity amplifier will not only enhance your vehicle's sound system, but it will also add a classy, visual flair. The Primus amplifier has on-board circuitry to protect them from shorts, temperature, overvoltage and undervoltage. An LED indicator is included on all four models to let you know when one of these conditions exists. Infinity takes its craft seriously and wants every consumer to have a world-class experience that lasts and lasts!
General Features
- 2-Channel Car Amplifier
- Preamp and speaker-level inputs
- Extruded Heatsink
- Low- and High-Level Inputs
- Switchable Bass EQ
- Onboard Active Crossover
- Full Conventional Protection Suite (OCP, OTP, OVP, UVP, DC)
- Fuse rating: 20A x 1
- 60 watts RMS x 2 at 4 ohms: 70 watts RMS x 2 at 2 ohms
- 140 watts RMS x 1 in bridged mode: 4-ohm stable in bridged mode
- Variable high/low-pass filters: 32-320 Hz, 12 dB/octave
- Variable bass boost: 0-12 dB at 45 Hz
UPC Code 050667373313
