2x JBL 6.5" 180W Marine White Speakers, 4-Channel Amplifier W/Kit, Controller
These JBL Stage Marine Speakers are ready to take on your next outdoor adventure. These fully marinized speakers not only deliver JBL sound, but they bring the sound to life. Engineered to withstand sun, salt, sea spray and wash downs, they feature sealed motor structure, UV resistant one-piece cast-polymer baskets and rubber surrounds. The polypropylene cone and balanced dome tweeter provide great bass, smooth highs and lots of output to ensure every note can be heard loud and clear. Marine-grade materials & components have been used to suit the demands of a harsh outdoor environment. These speakers feature an IPx5 marine rating.
General Features:
- 6-1/2" (160mm) Marine Two-way Speaker with 1/2" (13mm) tweeter
- Power Handling: 60W rms, 180W peak
- Sensitivity (@ 2.83V): 90dB
- Frequency Response: 60Hz – 20kHz
- Nominal Impedance: 4 ohms
- IPx5 Rated
- Grille Mounted Tweeters
- Polymer Basket
- Individually Voiced
- Harman Standard Reliability Tested
UPC Code 050036383103
This new weather-resistant amp; high-performance JBL Marine MA704 amplifier delivers impressive power from a compact chassis designed to withstand outdoor environments. With 4-channel outputs, this JBL Marine amplifier incorporates our latest amplifier topology that includes selectable all-, high-, or low-pass crossovers with variable electronic frequency adjustment for precision system tuning. Engineered for harsh marine conditions, with power and performance to meet the needs of any outdoor audio system, this amplifier is the perfect match for all of your JBL marine products.
Amplifier:
- 4 Channel Marine Amplifier
- Class D Technology
- Max Power - 1000W Peak
- Power Output, 2Ω - 100W RMS x 4
- Power Output, 4Ω - 70W RMS x 4
- Power Output, 4Ω Bridged - 200W RMS x 2
- Signal-to-Noise Ratio - ≥85dB
- High and low level inputs
- Variable crossovers and bass boost
UPC Code 050036346320
The Infinity by Harman INF-BC4 Pre-Amp Bluetooth Controller allows consumers to pair his/her media device, and control basic functions through the Infinity controller. This stand-alone audio device features a rotary encoder and large buttons. Add an amplifier, speakers, pair, and stream from the Infinity by Harman BT controller. Easily control the volume of your Bluetooth audio with the rotary controller. IPX6 Waterproof and ready for outdoor use; no need to worry about the forecast. Requires 1 3/8" diameter hole to secure firmly in place.
General Features:
- Requires 12V power source
- Requires 1 3/8" diameter hole
- Internal Blutetooth chipset
- Dimensions (W x D)2" x 2"
- Wireless Bluetooth Streaming
- Rotary Encoder
- IPX6 Waterproof
- Flush Mount
- Large Buttons
- Durably Constructed
UPC Code 050667372866
Renegade REN10KIT 10mm^2 Car Audio Complete Amplifier Installation Wiring Kit
General Features:
- 1 x 10 mm^2 Power Wire (red), flexible Strands (0,15 mm), 5 m
- 1 x 10 mm^2 Ground Wire (grey), flexible Strands (0,15 mm), 0.8 m
- 1 x RCA Stereo Audio Cable (blue), double shielded, 5 m
- 1 x 0.5 mm^2 Remote Wire, 5 m
- 1 x AGU Fuse Holder with 40 A ANL Fuse
- Installation Kit
Installation Instructions:
- Disconnect at first the negative ground connection from the vehicle’s battery.
- Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND contact point. Ensure that all paint or other insulation is removed from around the hole area.
- Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
- Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the supplied ring terminals.
- Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
- Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
- Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier, when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
- At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock consists. Then re-connect the negative ground connection to the vehicle’s battery.
UPC Code 854932002478
